Rhopoint Instruments Hardware and Software Manual
đź–¶
Introduction
Instruments and Hardware
Rhopoint Aesthetix
Getting Started
Specifications and Dimensions
Curved Surfaces & Non-Contact Measurement
Standard Adaptor (included with standard device)
Curved surface and small area gloss adaptor (included with standard device)
Novo Curve small aperture adaptor
Four-point rubber contact adaptor - small aperture
Four-point rubber contact adaptor
Three-point rubber contact adaptor - small aperture
Three‑point rubber contact adaptor
Bespoke jigs and fixtures
Non-Contact Small Area Gloss Adaptor (2mm)
Adaptor Mount
Laboratory Measurement Stand
Cobot and Inline Setup
Cleaning the Aesthetix
Storage and Handling
Packing List
Rhopoint TAMS
High Gloss Mode
Low Gloss Mode
Getting Started with TAMS
Calibrate the TAMS
Select Surface Type and Algorithim
Take a measurement
Batching Measurements
Setting up the batch and job database
Using the Job Mode
Using Manual Job Mode
Using Guided Job Mode
Specifications and Dimensions
Powering the TAMS
Cleaning the TAMS
Packing List
Software
Appearance Elements (AE)
Install AE
Start AE Software
AE Software Update
AE License Manager
Connect an Instrument to AE
Calibrating an Instrument in AE
Initiate a measurement(s) in AE
How to use AE without a license
Navigating the Main Screen
Action Bar
Device Manager
Module Bar
License Manager
Data Bar
Save and Load Data
Data Table
Viewing Measurement Images and Graphs
Batching Results
Statistical Analysis
Deleting Data
Systems Info
Screen Snip
Notification Alert
Help button
Using the Database
Using Aesthetix with AE
Aesthetix Modules
Visual demo module
Surface Brilliance
Surface Brilliance parameters
How to measure Surface Brilliance
Gloss Measurement Advice
Interpreting Gloss
How to Measure Curved Surfaces
Visual Gloss: for enhanced correlation with human perception
Surface Haze Measurement Guide
Visual Haze: predict haze visibilty in different viewing environments
Interpreting MC Michelson Contrast Haze
Waviness Measurement Guide
DOI & Sharpness Measurement Guide
Effect Finish Module
Effect Finish Parameters
Interpreting Effect Finish Parameters
Taking a Measurement- Effect Finish Module
Texture Module
Adjusting Texture Module User Parameters
Texture Module Parameters
Interpreting Surface Texture Results
Polishing Quality Module
Measuring Polish Quality
Adjusting Polishing Quality Parameters
Polishing Quality Parameters
Interpreting Polishing Quality Results
Linear Scratch Module
System Requirements
Measuring Linear Scratches
Linear Scratch Parameters
Cross-cut Module
How to Measure with Cross Cut Module
Cross Cut Adhesion Auto Mode
Cross Cut Adhesion Manual Mode
Cross-cut Module Measurement Guide
Cross-cut Parameters
Calibrating Aesthetix in AE
Ometrix
Taking Screen Shots
Copy and Paste
Trouble Shooting
Log Files
Device Connection Problems
TAMS with AE
TAMS Modules
Elements Hub (EH)
Changelog
Installation
Starting the application
Client Code Generation
Swagger UI Guide
Glossary of measurement parameters
10° Sparkle Measurement
60° Gloss (Aesthetix)
45° Sparkle Measurement
Ca- Cell Amplitude
Cn- Cell Number
Cs—Mean Cell Size
CsDev—Cell Size Standard Deviation
CsMax—Maximum Cell Size
CsMin—Minimum Cell Size
DOI Distinctness of Image (Aesthetix)
F—Fill Factor
Graininess
Haze and Compensated Haze
Hs—Hill Size
Michelson Contrast Haze MCH
R—Reflectivity
RC—Reflective Contrast
RH—Reflectivity on Hills
RGB Colour
RV—Reflectivity in Valleys
Sa Rough – Areal Surface Roughness
Scratch Parameters
Sharpness (Aesthetix)
Visual Gloss
Visual Haze
Unit: Perceived Microns [pµm]
Waviness (Aesthetix)
Quality (TAMS High Gloss)
Harmony (TAMS High Gloss)
Sharpness (TAMS High Gloss)
Waviness (TAMS High Gloss)
Contrast (TAMS High Gloss)
Dimension (TAMS High Gloss)
TAMS with AE
Start writing your section content here.