Rhopoint Instruments
Rhopoint Instruments Hardware and Software Manual
đź–¶
  • Introduction
  • Instruments and Hardware
    • Rhopoint Aesthetix
      • Getting Started
      • Specifications and Dimensions
      • Curved Surfaces & Non-Contact Measurement
        • Standard Adaptor (included with standard device)
        • Curved surface and small area gloss adaptor (included with standard device)
        • Novo Curve small aperture adaptor
        • Four-point rubber contact adaptor - small aperture
        • Four-point rubber contact adaptor
        • Three-point rubber contact adaptor - small aperture
        • Three‑point rubber contact adaptor
        • Bespoke jigs and fixtures
        • Non-Contact Small Area Gloss Adaptor (2mm)
        • Adaptor Mount
        • Laboratory Measurement Stand
      • Cobot and Inline Setup
      • Cleaning the Aesthetix
      • Storage and Handling
      • Packing List
    • Rhopoint TAMS
      • High Gloss Mode
      • Low Gloss Mode
      • Getting Started with TAMS
      • Calibrate the TAMS
      • Select Surface Type and Algorithim
      • Take a measurement
      • Batching Measurements
        • Setting up the batch and job database
        • Using the Job Mode
          • Using Manual Job Mode
          • Using Guided Job Mode
      • Specifications and Dimensions
      • Powering the TAMS
      • Cleaning the TAMS
      • Packing List
  • Software
    • Appearance Elements (AE)
      • Install AE
      • Start AE Software
      • AE Software Update
      • AE License Manager
      • Connect an Instrument to AE
      • Calibrating an Instrument in AE
      • Initiate a measurement(s) in AE
      • How to use AE without a license
      • Navigating the Main Screen
        • Action Bar
        • Device Manager
        • Module Bar
        • License Manager
        • Data Bar
          • Save and Load Data
        • Data Table
          • Viewing Measurement Images and Graphs
          • Batching Results
          • Statistical Analysis
          • Deleting Data
        • Systems Info
        • Screen Snip
        • Notification Alert
        • Help button
      • Using the Database
      • Using Aesthetix with AE
        • Aesthetix Modules
          • Visual demo module
          • Surface Brilliance
            • Surface Brilliance parameters
            • How to measure Surface Brilliance
            • Gloss Measurement Advice
            • Interpreting Gloss
            • How to Measure Curved Surfaces
            • Visual Gloss: for enhanced correlation with human perception
            • Surface Haze Measurement Guide
            • Visual Haze: predict haze visibilty in different viewing environments
            • Interpreting MC Michelson Contrast Haze
            • Waviness Measurement Guide
            • DOI & Sharpness Measurement Guide
          • Effect Finish Module
            • Effect Finish Parameters
              • Interpreting Effect Finish Parameters
            • Taking a Measurement- Effect Finish Module
          • Texture Module
            • Adjusting Texture Module User Parameters
            • Texture Module Parameters
              • Interpreting Surface Texture Results
          • Polishing Quality Module
            • Measuring Polish Quality
            • Adjusting Polishing Quality Parameters
            • Polishing Quality Parameters
            • Interpreting Polishing Quality Results
          • Linear Scratch Module
            • System Requirements
            • Measuring Linear Scratches
            • Linear Scratch Parameters
          • Cross-cut Module
            • How to Measure with Cross Cut Module
              • Cross Cut Adhesion Auto Mode
              • Cross Cut Adhesion Manual Mode
            • Cross-cut Module Measurement Guide
            • Cross-cut Parameters
        • Calibrating Aesthetix in AE
      • Ometrix
      • Taking Screen Shots
      • Copy and Paste
      • Trouble Shooting
        • Log Files
        • Device Connection Problems
    • TAMS with AE
      • TAMS Modules
    • Elements Hub (EH)
      • Changelog
      • Installation
      • Starting the application
      • Client Code Generation
      • Swagger UI Guide
    • Glossary of measurement parameters
      • 10° Sparkle Measurement
      • 60° Gloss (Aesthetix)
      • 45° Sparkle Measurement
      • Ca- Cell Amplitude
      • Cn- Cell Number
      • Cs—Mean Cell Size
      • CsDev—Cell Size Standard Deviation
      • CsMax—Maximum Cell Size
      • CsMin—Minimum Cell Size
      • DOI Distinctness of Image (Aesthetix)
      • F—Fill Factor
      • Graininess
      • Haze and Compensated Haze
      • Hs—Hill Size
      • Michelson Contrast Haze MCH
      • R—Reflectivity
      • RC—Reflective Contrast
      • RH—Reflectivity on Hills
      • RGB Colour
      • RV—Reflectivity in Valleys
      • Sa Rough – Areal Surface Roughness
      • Scratch Parameters
      • Sharpness (Aesthetix)
      • Visual Gloss
      • Visual Haze
      • Unit: Perceived Microns [pµm]
      • Waviness (Aesthetix)
      • Quality (TAMS High Gloss)
      • Harmony (TAMS High Gloss)
      • Sharpness (TAMS High Gloss)
      • Waviness (TAMS High Gloss)
      • Contrast (TAMS High Gloss)
      • Dimension (TAMS High Gloss)

Data Bar

image description

  1. Save Data
  2. Load Data
  3. Save to database
  4. Load from the database
  5. Delete selected/all measurements
  6. Open Ometrix
  7. Take a screen shot